Flash Profiler
2,5" SSD




Apacer 2,5" SATA III SSD SV240-25

Apacer’s SV240-25 is a well-balanced solid-state disk (SSD) drive with standard form factor and great performance. Designed in SATA 6 Gb/s interface, the SSD is able to deliver exceptional read/write speed, making it the ideal companion for heavy-loading industrial or server operations.

SV240-25 utilizes 3D NAND for higher capacity up to 1920GB and provides more power efficiency than 2D NAND. Regarding reliability, SV240-25 is implemented with LDPC (Low Density Parity Check) ECC engine to extend SSD endurance and increase data reliability while reading raw data inside a flash chip. In addition, the drive comes with various implementations including powerful hardware ECC engine, power saving modes, wear leveling, flash block management, S.M.A.R.T., TRIM, and DataDefender.

Model No.
SV240-25
Interface
SATA III 6.0 Gb/s
Capacity
120GB - 1920GB
Flash Type
3D TLC
Endurance
3.000 P/E Cycles
Standard Temperature
0°C - +70°C
Extended Temperature
-40°C - +85°C
Performance
SR: 560MB/s | SW: 505MB/s
DRAM
Yes

acon 2,5" SATA III SSD T/TX 420

acon’s 2.5” SATA Solid State Disk (SSD) delivers all the advantages of flash disk technology with the Serial ATA I/II/III interface, including being fully compliant with standard 2.5-inch form factor, providing low power consumption compared to traditional hard drive and hot-swapping when removing/replacing/upgrading flash disks. The device is designed based on the standard 7-pin interface for data segment and 15-pin for power segment, as well as operating at a maximum operating frequency of 400MHz with 25MHz external crystal. Its capacity could provide a wide range up to 8TB. Moreover, it can reach up to 550MB/s read as well as 530MB/s write high performance based on TSB BiCS3 3D TLC flash.

Model No.
T/TX420
Interface
SATA III 6.0 Gb/s
Capacity
240GB - 8TB
Flash Type
3D TLC
Endurance
3.000 P/E Cycles
Standard Temperature
0°C +70°C
Extended Temperature
-40°C +85°C
Performance
SR: 560MB/s | SW:530MB/s
DRAM
Yes

Apacer 2,5" SATA III SSD SV250-25

Apacer’s SV250-25 is a well-balanced solid-state disk (SSD) drive with standard form factor and great performance. Designed in SATA 6.0 Gbps interface, the SSD is able to deliver exceptional read/write speed, making it the ideal companion for heavy-loading industrial or server operations.

SV250-25 utilizes 3D NAND and provides more power efficiency than 2D NAND. Regarding reliability, SV250-25 is implemented with LDPC (Low Density Parity Check) ECC engine to extend SSD endurance and increase data reliability while reading raw data inside a flash chip. In addition, the drive comes with various implementations including powerful hardware ECC engine, power saving modes, wear leveling, flash block management, S.M.A.R.T., TRIM, and DataDefender™.

Model No.
SV250-25
Interface
SATA III 6.0 Gb/s
Capacity
30GB - 960GB
Flash Type
3D TLC
Endurance
3.000 P/E Cycles
Standard Temperature
0°C +70°C
Extended Temperature
-40°C +85°C
Performance
SR: 560MB/s | SW: 520MB/s
DRAM
No

acon 2,5" SATA III SSD T/TX 410

acon 2.5” SATA Solid State Disk (SSD) delivers all the advantages of flash disk technology with the Serial ATA I/II/III interface, including being fully compliant with standard 2.5-inch form factor, providing low power consumption compared to traditional hard drive and hot-swapping when removing/replacing/upgrading flash disks. The device is designed based on the standard 7-pin interface for data segment and 15-pin for power segment, as well as operating at a maximum operating frequency of 200MHz with 30MHz external crystal. Its capacity could provide a wide range up to 1TB. Moreover, it can reach up to 550MB/s read as well as 500MB/s write high performance based on 16CE and Toggle 2.0 TLC flash (with 32MB SDR enabled and measured by CrystalDiskMark v5.0).

Model No.
T/TX410
Interface
SATA III 6.0Gb/s
Capacity
32GB - 1TB
Flash Type
3D TLC
Endurance
3.000 P/E Cycles
Standard Temperature
0°C +70°C
Extended Temperature
-40°C +85°C
Performance
SR: 550MB/s | SW: 500MB/s
DRAM
No

Model Nr.
Interface
Kapazität
Flash Typ
MTBF (Std.)
Standard Temperatur
Erweiterte Temperatur
Lesegeschwindigkeit
Schreibgeschwindigkeit

Model Nr.
Interface
Kapazität
Flash Typ
MTBF (Std.)
Standard Temperatur
Erweiterte Temperatur
Lesegeschwindigkeit
Schreibgeschwindigkeit

Model Nr.
Interface
Kapazität
Flash Typ
MTBF (Std.)
Standard Temperatur
Erweiterte Temperatur
Lesegeschwindigkeit
Schreibgeschwindigkeit

Model Nr.
Interface
Kapazität
Flash Typ
MTBF (Std.)
Standard Temperatur
Erweiterte Temperatur
Lesegeschwindigkeit
Schreibgeschwindigkeit

Model Nr.
Interface
Kapazität
Flash Typ
MTBF (Std.)
Standard Temperatur
Erweiterte Temperatur
Lesegeschwindigkeit
Schreibgeschwindigkeit

Model Nr.
Interface
Kapazität
Flash Typ
MTBF (Std.)
Standard Temperatur
Erweiterte Temperatur
Lesegeschwindigkeit
Schreibgeschwindigkeit

Model Nr.
Interface
Kapazität
Flash Typ
MTBF (Std.)
Standard Temperatur
Erweiterte Temperatur
Lesegeschwindigkeit
Schreibgeschwindigkeit


Diese Webseite verwendet Cookies. Mit der Nutzung unserer Dienste erklären Sie sich damit einverstanden, dass wir Cookies verwenden: Weitere Informationen